Installation Guide :: essays research papers

1This product can be set up usingan any y curr curren en ent t weathervane br browser owser owser, , i.e e., .,Internet Explorer 6 or NetscapeNavigator 6.2.3.DI-524Air AirPlus Plus G 802.11g/2.4GHzWireless Router5V DC exponent Adapter2003 D-Link Systems, Inc. both rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software andspecifications subject to change without notice. DI-524. 11142003Before You Begin1. If you purchased this router to share your high-speed Internet fellowship with othercomputers, you must have either an Ethernet-based note or digital subscriber line modem with anestablished Internet account from an Internet Service Provider (ISP).2. Its high hat to use the kindred computer that is tie ined to your modem for configuringthe DI-524 AirPlus G Wireless Router. The DI-524 acts as a DHCP server and willassign all the necessary IP oral communication information on your network. See Appendix atthe end of this Qui ck Installation Guide or the Manual on the CD-ROM forsetting for each one network adapter to automatically obtain an IP address.Check Your Package ContentsDI-524 AirPlus G 802.11g/2.4GHz WirelessRouterCD-ROM (containing Manual and Warranty)Ethernet (CAT5 UTP/Straight Through) Cablevictimization a might supply witha different voltage rating willdamage and void the warrantyof this product.If any of the above items are missing, ravish contact your reseller.TM2 get togethering The DI-524 Wireless RouterTo Your NetworkA. Receptor forPower Adapter.Reset ButtonPressing this button restores the Router to its originalfactory default settings.A. First, connect the cater adapter to the receptor at the back down panel of theDI-524 and then plug the other end of the power adapter to a wall progeny or powerstrip. The Power LED lights up indicating proper operation.B. 1. Power by your Cable or DSL modem devices that do not have a on/off switch andwill require you to unplug the power adapt er. Now, the DI-524 should be powered onand the Cable / DSL modem should be turned off.Cable / DSL modem (Power Off) DI-524 (Power On)2. Connect an Ethernet cable to the Ethernet jack located on the Cable / DSLmodem. After the Ethernet cable is securely connected, power on the Cable / DSLmodem by round on the unit or plugging in the power adapter.Cable / DSL modem (Power On) DI-524 (Power On)3. Insert the other end of the Ethernet cable to the WAN appearance on the back panel ofthe DI-524. The WAN LED light will illuminate to indicate proper connection. If theWAN LED is not illuminated, please go back to pace B1 and repeat the steps.Installation Guide essays research papers 1This product can be set up usingan any y curr curren en ent t web br browser owser owser, , i.e e., .,Internet Explorer 6 or NetscapeNavigator 6.2.3.DI-524Air AirPlus Plus G 802.11g/2.4GHzWireless Router5V DC Power Adapter2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks a re the property of their respective holders. Software andspecifications subject to change without notice. DI-524. 11142003Before You Begin1. If you purchased this router to share your high-speed Internet connection with othercomputers, you must have either an Ethernet-based Cable or DSL modem with anestablished Internet account from an Internet Service Provider (ISP).2. Its best to use the same computer that is connected to your modem for configuringthe DI-524 AirPlus G Wireless Router. The DI-524 acts as a DHCP server and willassign all the necessary IP address information on your network. See Appendix atthe end of this Quick Installation Guide or the Manual on the CD-ROM forsetting each network adapter to automatically obtain an IP address.Check Your Package ContentsDI-524 AirPlus G 802.11g/2.4GHz WirelessRouterCD-ROM (containing Manual and Warranty)Ethernet (CAT5 UTP/Straight Through) CableUsing a power supply witha different voltage rating willdamage and void the warrantyof this product.If any of the above items are missing, please contact your reseller.TM2Connecting The DI-524 Wireless RouterTo Your NetworkA. Receptor forPower Adapter.Reset ButtonPressing this button restores the Router to its originalfactory default settings.A. First, connect the power adapter to the receptor at the back panel of theDI-524 and then plug the other end of the power adapter to a wall outlet or powerstrip. The Power LED lights up indicating proper operation.B. 1. Power off your Cable or DSL modem devices that do not have a on/off switch andwill require you to unplug the power adapter. Now, the DI-524 should be powered onand the Cable / DSL modem should be turned off.Cable / DSL modem (Power Off) DI-524 (Power On)2. Connect an Ethernet cable to the Ethernet jack located on the Cable / DSLmodem. After the Ethernet cable is securely connected, power on the Cable / DSLmodem by turning on the unit or plugging in the power adapter.Cable / DSL modem (Power On) DI-524 (Power On)3. Insert the other end of the Ethernet cable to the WAN PORT on the back panel ofthe DI-524. The WAN LED light will illuminate to indicate proper connection. If theWAN LED is not illuminated, please go back to step B1 and repeat the steps.